Engineering, Civil - AS to BS - The University of Texas at San Antonio (UTSA) 2017-2018

Lower Division Requirements at the Alamo Colleges District for an AS degree

The courses in this section meet the requirements for an Associate of Science degree. The Graduation section in any catalog of the colleges in the Alamo Colleges District lists additional Degree/Certificate Requirements.

Applicable Transfer Credit Hours

This Transfer Advising Guide provides 75 college-level hours, of which 62 will transfer and apply as EDUC 1300, MATH 1414, MATH 2412, 1 SCH of ENGR 1201 and 1 SCH from MATH 2421 will transfer, but will NOT be applicable to the UTSA baccalaureate degree in Civil Engineering.

Note: UTSA accepts a maximum of 66 college-level hours in transfer towards a baccalaureate degree

Note: For the Alamo Colleges District this transfer advising guide is core complete and degree complete, but is NOT field of study complete

Milestone Course(s)

*** denotes Milestone Course(s).

A milestone course is a course that is critical for success in this program as determined by the Faculty of the Alamo Colleges District.

Gateway Course(s)

### denotes Gateway Course(s)

Students pursuing this degree at UTSA must successfully complete each of the Gateway Courses with a grade of “C” or better in no more than two attempts.  A student who is unable to successfully complete these courses within two attempts, including dropping a course with a grade of “W” or taking an equivalent course at another institution (including any colleges of the Alamo Colleges District), will not be allowed to select this major at UTSA.

Field of Study Curriculum for Engineering

§ denotes THECB Field of Study Curriculum Course

The Engineering Field of Study is designed to promote maximum transferability for students while still preserving appropriate curricular diversity for institutions. Engineering is a very broad field that covers many disciplines; consequently, there is significant variance in engineering curricula among our state institutions.

Additional information can be found at http://www.thecb.state.tx.us/reports/PDF/1761.PDF?CFID=69475177&CFTOKEN=92398439

Special College Admission Requirements for The College of Engineering at the University of Texas at San Antonio

Mechanical Engineering, Civil Engineering, Electrical Engineering, Computer Engineering

Special Department Admission Requirements

Transfer Students: The following are the transfer requirements for direct admission to the Civil Engineering (CE) major, for transfer students who have earned 30 or more credits:

• MAT 1214 Calculus I, or the equivalent with a grade of “C-” or better.
• Meet GPA requirements:

1.     Have a transfer grade point average of at least 2.50 and a grade point average of at least 2.50 in all mathematics, sciences, and engineering coursework, OR

2.     Have a transfer grade point average of at least 2.25 and a grade point average of at least 2.25 in all mathematics, sciences, and engineering coursework, and be granted admission to the College of Engineering major by ­holistic review by the College.

Transfer students not admitted directly into the College of Engineering will be changed to Undeclared (UND) and must choose another major outside of engineering.

Degree Requirements Common to All Engineering Programs

During their first semester, students should specify their interest in a specific engineering program by selecting biomedical, chemical, civil, computer, electrical, or mechanical engineering as a major. Undecided engineering students should select a major closest to their area of interest (refer to the following program descriptions). Students may obtain additional information about each program from their academic advisor or a faculty advisor in the appropriate department.

Prerequisites for Biomedical Engineering (BME), Chemical Engineering (CME), Civil Engineering (CE), Computer Engineering (CPE), Electrical Engineering (EE), Mechanical Engineering (ME), and Engineering (EGR) courses must be completed with a grade of “C-” or better. A minimum grade of “C-” is required for all science and mathematics courses required in the Engineering programs. Students must satisfy the University’s Core Curriculum and ABET accreditation requirements. Recommended degree plans and current ABET requirements may be obtained from the College of Engineering.

All students admitted to the College of Engineering must complete at least 42 semester credit hours from their required major courses at UTSA before graduation.

Three Attempt Limit

A student unable to acheive the “C-” Grade Rule in a required engineering course or in a prerequisite to a required engineering course within three enrollments (attempts) shall be required to change his or her major to a field outside of the College of Engineering. Dropping a course with a grade of a “W” is considered an attempt.

Additional UTSA Advising Notes

Things to do and remember upon Admission to UTSA:

• Make an appointment with the academic advisor of the major, once accepted to UTSA, in order to clarify department, college and university policies and procedures, to review course sequencing and to help with identifying resources for academic success. A current listing of academic advising centers can be found at www.utsa.edu/advise/advisors.html.
• Refer to the official source of information on specific courses within the UTSA requirements for this degree plan from the UTSA Undergraduate Catalog or visit the web site at www.utsa.edu.
• Information on Gateway Courses can be found at http://www.utsa.edu/registrar/students/gateway.html.
• Read the UTSA Undergraduate Catalog and Student Information Bulletin.
• Pay close attention to course sequencing and availability at UTSA as it will affect the time it takes to complete the degree program.

Using this Transfer Advising Guide with UTSA

This Transfer Advising Guide represents UTSA’s degree plan and is subject to change at the university’s discretion. It is intended for advising purposes only so students know exactly which courses they can take at any of the colleges in the Alamo Colleges District and have the courses count towards degree requirements when they transfer to UTSA. It is highly recommended that students meet with their assigned academic advisor to review all graduation and transfer requirements listed in the Transfer Advising Guide.

The ultimate goal is to provide students with accurate information for transfer pathways while minimizing loss of credits in transfer. Students are encouraged to review UTSA’s requirements frequently.

Course numbers in italics are UTSA’s course numbers.

This Transfer Advising Guide is based upon The University of Texas at San Antonio’s 2017-2018 catalog and is subject to change.

The Alamo Colleges District Advising

Students are encouraged to consult with an academic advisor about courses and other educational concerns if they plan to pursue a two-year degree program, transfer to another college or university, or simply take a few selected courses. In addition to course and degree requirements, policies and procedures are subject to change; stay informed by meeting with an academic advisor regularly.

Many students who plan to transfer to a university are advised to fulfill the lower-division requirements for the university. With appropriate planning, your Alamo Colleges District team can help make the transfer experience a seamless process. It is the responsibility of all students to ensure that they take courses at the Alamo Colleges District that will be accepted by the senior institutions they wish to attend.

For more information contact your Alamo Colleges District team.

Release Date:

Release Date: March 28, 2018